loader
unifilogo_Round

Unifi Operating System

Version 3.2.12
  • UniFi OS 3.2.12 includes the improvement and bugfixes listed below.
  •  UniFi Network 8.0.28
  • Improved configuring fixed speed on SFP ports when the module has a faulty EEPROM.
  • Fixed the inability to send Identity Standard invites.
  • Fixed redundant logging to /dev/tty10.
unifilogo_Round

Unifi Network Application

Version 8.0.28
  • UniFi Network Application 8.0.28 includes the bugfixes listed below.
  • Fixed the inability to upload hotspot landing page images on consoles running the Native Application (UDR, UDM, Express).
  • Fixed the inability to see the DNS Shield setting in rare cases.
  • Fixed the inability to open Security Logs in rare cases.
  • Fixed the inability to select multiple APs in Display Options on the Clients page.
  • Fixed the inability to update Virtual Networks from the Topology page when DHCP Guarding or DHCP Options are enabled.
  • Fixed the inability to see devices that are Pending Adoption as Site Administrator on Network Application Servers.
  • Fixed an issue where mesh links went down due to an invalid Monitor IP Address for Wireless Meshing after updating to Network Application 7.5 or newer and Access Point firmware version 6.6.12 or newer.
  • Fixed gateway configuration/provisioning issues when the WAN interface can’t be found.
  •  
unifilogo_Round

Unifi Protect Application

Version 3.0.26
  • UniFi Protect Application 3.0.26 improves face recognition performance and application stability.
  • Improved face recognition performance in rare cases.
  • Improved application resiliency.
  • Fixed an issue where video archiving folders were not using the configured timezone.
  • Fixed an issue with fullscreen digital zoom in Timelapse.
  • Fixed the inability to see recordings on setups with modified certificates.

Unifi Operating System

Version 3.2.7

Unifi Network Application

Version 8.0.26

Unifi Protect Application

Version 2.10.10
  • UniFi OS – Dream Machines 3.2.7 adds support for Subscription Free UniFi Identity, Shadow Mode, InnerSpace, VLAN Magic, DNS Shield and Loop Protection. 

With Shadow Mode on the UDM-Pro, you can ensure High Availability (HA) of your network’s gateway to minimize downtime, and provide a reliable failover mechanism in the face of unexpected hardware failures. In this setup, a secondary Cloud Gateway mirrors the configuration of the primary one, and can easily take over full network and management capabilities should it ever fail. See the Shadow Mode Help Center article for more information.

Currently, Shadow Mode operates as a “Warm Spare,” meaning some manual intervention is required, however this will become fully automated in an upcoming release.

The UniFi InnerSpace Application is a powerful deployment visualization tool that allows you view your UniFi system’s WiFi and camera coverage over your own floor plan. InnerSpace replaces the Map option in the Console Settings.

With VLAN Magic, you can quickly create a new Virtual Network and associate devices to this VLAN by selecting them on the Topology

The new DNS Shield feature ensures privacy and security of DNS traffic by encrypting it using DNS over HTTPS (DoH).

The new Loop Protection feature automatically disables ports on which loops are detected. It does not depend on Spanning Tree and even works when neighboring devices do not support STP. Enable Loop Protection on all UniFi Gateway and UniFi Switch ports via the Port Manager. Ports that are disabled by Loop Protection need to be manually re-enabled.

  • Added Subscription Free UniFi Identity.
  • Set up UniFi Identity via the Admins & Users > Users section.
  • [UDM-PRO] Added Shadow Mode.
  • Added InnerSpace application replacing the Map option in the Console Settings.
  • Added VLAN Magic.
  • Added DNS Shield.
  • Added Loop Protection.
  • Added hostname support for IPsec Site-to-Site VPNs.
  • Added the console’s IP address during setup on the Touchscreen.
  • Added max login attempts for SSH.
  • Entering incorrect credentials 5 times will block for 3 minutes.
  • Added fallbacks to default timezones if unsupported ones are provided during setup.
  • Added DNS warnings for consoles that cannot resolve the ui.com domain.
  • Allow disabling Remote Access where there are connection issues.
  • Improved various screens on the Touchscreen.
  • Improved detection of failed disks.
  • Disks that cannot initialize will be marked as broken.
  • Improved RADIUS stability.
  • Improved WireGuard VPN disconnection detection for mobile devices.
  • Consoles will no longer erase external storage during a factory reset.
  • Updated Suricata to 6.0.12.
  • Reduced the console reset button count down from 10 seconds to 5 seconds.
  • Updated the UniFi Logo in the local portal.
  • Reduced memory usage of Suspicious Activity, Content Filtering, and Ad Blocking.
  • Prevent super admins from deleting their own account.
  • [UDM] Added LED night mode scheduling.
  • [UDM] Updated the fan behavior under high temperature.
  • [UDM] Updated integrated Access Point firmware to 6.6.54.
  • Added DNS resiliency for firmware updates.
  • Improved UniFi OS backup resiliency.
  • Improved meshing stability when consoles are restarting or upgrading.
  • Consoles will now always store backups locally before upgrading the firmware.
  • Auto recovery is in place in case there is file system corruption after a power outage.
  • Reduced network downtime for firmware upgrades.
  • Fixed an issue where the IPv6 address is lost after interface changes until the next RA.
  • Fixed unable to start RADIUS service in rare cases.
  • Fixed incorrect WAN IP on the portal after remapping the WAN ports.
  • Fixed an issue with DNS servers for VPN Client. This applies to the VPN Client feature, not adding clients to VPN Servers.
  • Fixed an issue where servers are not reachable for VPN Client due to incorrect certificates. This applies to the VPN Client feature, not adding clients to VPN Servers.
  • Fixed an issue where the default route wasn’t present when using a static IP on the WAN port.
  • Fixed an issue where IGMP Proxy breaks after PPPoE reconnections.
  • Fixed an issue where Traffic Routes didn’t take effect for existing connections.
  • Fixed an issue where Traffic Routes conflicted with Content Filtering.
  • Fixed inability to see DPI statistics for setups with large amounts of clients.
  • Fixed unexpected behavior when there are multiple Traffic Rules blocking the same domain.
  • Fixed unable to establish IPsec Site-to-Site VPN in rare cases.
  • Fixed an issue where jumbo frames are forwarded on LAN ports when Jumbo Frames is disabled.
  • Fixed an issue where PPPoE MSS Clamping is lost during provisions.
  • Fixed Suspicious Activity not working when enabling Jumbo Frames.
  • Fixed an issue where WAN2 configurations were removed after a firmware upgrade when using 8.0.24 with a Static or PPPoE WAN configuration.
  • This only prevents new occurrences. Affected setups need to be restored from a backup before this issue or re-create their WAN config.
  • Fixed gateway/console showing offline when WAN interface cannot be found.
  • Improved application stability.
  • Improved UX when configuring Internal Relay Chime settings on Doorbells.
  • Consolidated network outage events for all disconnected cameras.
  • Updated the bundled Camera FW to 4.68.17.
  • Fixed an issue where the Floodlights would appear disconnected if the Console IP changed.
  • Fixed application restore loop when using invalid backup files.
  • Fixed an issue where a UP-Sense could get stuck in a Getting Ready status.
  • Fixed package detections to support multiple thumbnail formats.
  • Fixed System logs showing results for the following days outside the filter scope.
  • Fixed update related System Log category.
  • Fixed displaying water leak events in the Activities tab and System Log.
  • Fixed messaging after changing settings for stacked NVRs.
  •  

Version 3.1.16

Version 8.0.7

Version 2.9.42
  • UniFi Network Application 8.0.7 adds support for Radio Manager, WireGuard VPN Client, and Site Overview, and improves the Port Manager section by adding an overview of all ports and the VLAN Viewer.
  • The new Radios page provides an overview of the Access Point radios and their configuration, statistics, and performance.

    • Filter Devices – Show all APs or only specific devices.
    • Filter Bands – Use the filters to display only certain bands or MIMO, e.g. 5 GHz or 3×3.
    • Bulk Edit – Change the radio configuration on multiple APs at the same time.
  • The new Ports page provides an overview of all ports across your devices.

    • Filter Ports – Use the filters to display only certain ports, e.g. only PoE or SFP ports.
    • Filter Devices – Show all ports or only ports on a specific device.
    • Insights – View and compare statistics between ports on the same device.

The VLAN port management has been redesigned to improve UX when managing VLANs.

  • Native VLAN / Network – Used for untagged traffic, i.e. not tagged with a VLAN ID. Previously this option was called ‘Primary Network’.
  • Tagged VLAN Management – Used for traffic tagged with a VLAN ID. Previously this option was called ‘Traffic Restriction’.
  • Allow All – Configured VLANs are automatically tagged (allowed) on the port.
  • Block All – All tagged VLANs are blocked (not allowed) on the port.
  • Custom – Specify which VLANs are tagged (allowed) on the port. Any VLAN that is not specified is blocked.

When adding a new VLAN, it is automatically tagged (allowed) on the port when using ‘Allow All’. If ‘Custom’ is used, the new VLAN needs to be manually added to the port.

  • Provides an easy way to see Native and Tagged VLANs across your devices.

    • Native VLAN Assignment – This shows which VLAN ID is set as native.
    • VLAN Tagging – Shows which VLANs are tagged, blocked, or native.
    • Search for VLANs using the VLAN name, ID, or subnet.
  • WireGuard VPN Client

    Allows you to connect your UniFi Gateway to a VPN service provider and send internet traffic from devices over the VPN. Uploading a file and manual configuration are both supported.

Provides an overview of all sites used on UniFi Network Applications managing multiple sites.

  • UniFi Devices – See how many devices are connected to each site.
  • Client Devices – See how many WiFi/wired clients and guests are connected to each site.
  • Insight – See which sites have offline devices and critical notifications.

The System Log now provides much more details on client connections such as the connection time and data usage.

  • Improved Port Manager.
  • Added all ports overview.
  • Added VLAN Viewer.
  • Improved VLAN port management UX.
  • Added Site Overview.
  • Added ability to select which networks Suspicious Activity is enabled on.
  • Added sorting feature for IP Groups.
  • Added ability to allow opening predefined firewall rules.
  • Improved validation for Prefix ID in Virtual Network settings.
  • Improved empty MAC whitelist validation in Port Manager.
  • Improved validation for DHCP options.
  • Improved DHCP Server TFTP Server field validation.
  • Improved Traffic Rule IP Address validation.
  • Improved Firewall Rules UX.
  • Improved Security Settings UX.
  • Improved Global Network Settings UX.
  • Enabled auto upgrade for UXG-Pro after the adoption is completed.
  • Remove LTE Failover WAN from IPTV Options.
  • Show the local language in the Language dropdown.
  • Prevent provisioning more Layer 3 static routes than UniFi switches can support.
  • Routes that are over the limit at the time of upgrade will be marked as Paused.
  • This does not mean that total static route support on Layer 3 UniFi switches is decreased, instead, UX is improved to prevent configuration of routes that are not functional.
  • Added WireGuard VPN Client.
  • Added messaging to create traffic routes after creating VPN Clients. This applies to the VPN Client feature, not adding clients to VPN Servers.
  • Added validation in VPN Server settings when the port overlaps with a Port Forwarding rule.
  • Added IP/Hostname override option for OpenVPN and WireGuard VPN Servers.
  • This adds a custom hostname or IP address to the configuration file used by clients.
  • This option is useful if the UniFi Gateway is behind NAT or is using a dynamically assigned IP address.
  • Added validation for Local IP in IPsec Site-to-Site VPN settings.
  • Automatically remove Site-to-Site Auto IPsec configuration if the adopted gateway doesn’t support it.
  • Improved Site-to-Site VPN validations.
  • Improved configuration file generation time for OpenVPN Servers.
  • Increased OpenVPN and WireGuard VPN Client limit from 5 to 8. This applies to the VPN Client feature, not VPN users connecting to VPN Servers.
  • Remove the PPTP Server if the adopted gateway doesn’t support it.
  • Added PoE power cycle option to the device side panel.
  • Added confirmation message when configuring Network Overrides.
  • Improved UniFi Devices page performance on larger setups.
  • Improved System Logs for client connections.
  • Locked the first column for Devices/Clients pages when scrolling horizontally.
  • Client hostnames (if present) are now shown in the side panel overview.
  • Moved filters to the left side in the Device and Client pages.
  • Added Radio Manager.
  • Added ability to enable Professional installer toggle for Consoles.
  • Improved adding clients to MAC Address Filters.
  • Improved actionable feedback when Outdoor Mode is enabled.
  • Removed Global AP Settings, you can now use Radio Manager for bulk editing.
  • Collapse RF Scan tab by default in the AP device panel.
  • Changed WiFi Experience to TX retries for APs in their device panel.
  • Enhanced voucher printing options.
  • Fixed an issue where some UniFi devices were incorrectly shown on the Client Devices page or not shown at all.
  • As a result of this fix, unmanaged non-network UniFi devices (e.g. UniFi Protect camera) may appear again as offline devices.
  • These offline devices will be removed automatically based on the Data Retention settings.
  • Automatic removal is an automated, periodic process that will run for several minutes after updating. Manual removal is also possible.
  • Fixed an issue where blocked clients couldn’t connect if they were removed until the next AP provision.
  • Fixed incorrect channel width for BeaconHD/U6-Extender.
  • Fixed an issue where Virtual Network usable hosts were incorrectly calculated.
  • Fixed missing ISP names in internet-related notifications.
  • Fixed rare gateway adoption issues via Layer 3.
  • Fixed an issue where WiFiman speed test results were not shown.
  • Fixed issue where WAN configuration is not populated when moving a gateway device to a new site.
  • Fixed an issue where CGNAT IP addresses were incorrectly marked as public IPs for Site Magic.
  • Fixed invalid connected client count for In-Wall APs.
  • Fixed unmanaged Network devices not shown on Client and Device pages in rare cases.
  • Fixed an issue where the Console would appear offline in rare cases.
  • Fixed sorting when there are multiple pages.
  • Fixed an issue where Voice VLAN settings are not effective when all VLANs are auto-allowed on switch ports.
  • Fixed an issue where Lock to AP is not disabled when removing an AP.
  • Fixed an issue where RADIUS profiles couldn’t be disabled when using a WireGuard VPN Server.
  • Fixed rare gateway configuration error.

UniFi Protect Application 2.9.42 enhances the video retrieval functionality by implementing license plate search as well as local UniFi Access integration. In addition, this release introduces an improved device notification and global recording settings user experience.

Easily locate all prior recordings of a specific vehicle captured by AI-series cameras by searching for its license plate number on the Detections page.

When UniFi Access and UniFi Protect are running on the same console, you can now pair a Protect camera to an Access Hub, enabling Door Access events to be shown in both Detections and Timeline view, including the name of the user who opened the door (if available).

  • Added new Notification settings under System Logs.
  • Added support for the door access detection event in the Detection page and playback timeline. (depends on Access integration)
  • Added the most active camera section in the Dashboard.
  • Added support for multiple thumbnails for detection.
  • Added support for LPR search on the detection page.
  • Added more layouts to Live View.
  • Added support for line crossing count in Live View.
  • Added Removed status in the display options within the detection page.
  • Added Max Sound Intensity in the Dashboard page.
  • Added device adoption instructions in the Devices list.
  • Added device factory reset instructions in the Devices Property panel.
  • Added messaging when more disks are required.
  • Added support for updating device firmware outside of bundled upgrades.
  • Added the ability to export clips from the Package Camera on the detections page.
  • Added support exit/entry information for door access events.
  • Added global recording mode changes to system logs.
  • Added information with instructions when a wireless camera is removed.
  • Added notification section to the UP-Sense device property panel.
  • Added notification section to the Floodlight device property panel.
  • Added support for disconnection System Logs for non-camera devices.
  • Improved validation for schedule and geolocation notifications.
  • Improved missing or delayed Doorbell ring notifications.
  • Improved system logs for “Global Recording Settings” changes.
  • Improved resolution messaging for wireless/wired cameras.
  • Improved schedule selected time validation.
  • Improved UX responsiveness of Push Notification Settings.
  • Improved visible thumbnail when opening an event and while the video is loading.
  • Improved the UX in the Detections page.
  • Improved the loading speed of thumbnails.
  • Improved messaging across the application.
  • Improved application stability.
  • Updated LiveView/Detection Player Header style.
  • Updated previewing schedule on the camera side panel.
  • Updated the bitrates for image quality as absolute value instead of percent.
  • Updated pagination mechanism for detections page.
  • Updated the product name from ‘ViewPort’ to ‘Viewport’.
  • Updated Global Recording Settings and improved the UX.
  • Updated Chime PoE firmware to 1.4.5.
  • Updated Chime firmware to 1.4.6.
  • Updated Floodlight firmware to 1.11.2.
  • Updated Viewport firmware to 1.3.127.
  • Updated Camera firmware to 4.66.16.
  • Fixed an issue where users could see “Storage Not Found” messages during initialization.
  • Fixed an issue where users could configure invalid Sensitivity settings.
  • Disable the Download & Delete button if the storage is corrupted on the Playback page.
  • Fixed the issue where person and vehicle events were not supported in the Graph View.
  • Fixed an issue where users saw the ability to download the non-recorded video footage.
  • Fix incorrect event display on Timelapse.
  • Fixed an issue where UP-Sense would stop reporting humidity values.
  • Fixed the inability to set the device’s name during adoption.
  • Fixed some package detection clips that cannot be played.
  • Fixed incorrect start time for detections.
  • Fixed the camera capacity, which should not be affected by permissions.
  • Fixed audio information should only be available on the dashboard when cameras are recording.
  • Fixed rare application crashes.
  • Fixed incorrect camera messaging in System Logs when cameras updated.
  • Fixed incorrect usernames for admin/user activity in system logs.
  • Fixed incorrect usernames for deactivated admins/users in system logs.
  • Fixed wrong Ethernet status on UP-Chime-POE while online.
  • Fixed incorrect recording retention duration when the retention setting was changed from Auto to Custom.
  • Fixed available recording options when UNVR doesn’t have an HDD.
  • Fixed issues with saving retention settings.
  • Fixed issue, when thumbnails appeared stuck in loading.
  • Fixed button titles in the zone editor.
  • Fixed an issue with removing detections when removing a camera.
  • Fixed an issue where the Dewarp option isn’t showing for the AI-360 on the LiveView page.
  • Fixed an issue where the application couldn’t auto-recover properly.
  • Fixed a rare issue where old recordings might get lost after a restart.
  • Fixed the inability to export long clips in rare cases.
  • Fixed an issue where Smart Detection events are still recorded while disabled.
  • Allow configuring what Motion / Smart Detections to record. *

* If you’re upgrading from any 2.9 version, please check your recording and motion event preferences.

Version 3.1.16

Version 7.5.187

Version 2.8.35

UniFi OS – Dream Machines 3.1.16 includes the improvements and bugfixes listed below..

  • Added the console’s IP address to the touchscreen during setup.
  • Improved backup restore resiliency.
  • Improved stability of installing dependencies.
  • Improved device stability.
  • Updated the AR pattern on the touchscreen.
  • Updated integrated Access Point firmware to 6.5.64.
  • Renamed UniFi UID to UniFi Identity.
  • Fixed high CPU usage caused by Traffic Identification.
  • Fixed an issue where jumbo frames were being forwarded to LAN ports while it was disabled.
  • Fixed unable to reach the internal subnet from L2TP/Teleport VPN Clients.
  • Fixed routing table issue when both WANs are configured with the same subnet.
  • Fixed issue where QoS on WAN1 affects WAN2 traffic.
  • Improved Network Application startup for large setups.
  • Fixed an issue where you might see a blank Guest Portal in rare cases.
  • Fixed Dashboard Active Channels showing recently disabled radios/channel 0 as active.
  • Fixed WiFi channel options missing when creating new sites.
  • Fixed an issue where WiFi PPSK didn’t work with VLAN Only Networks.
  • Fixed an issue where users couldn’t delete Auto IPsec S2S VPNs.
  • Fixed gateway configuration errors in rare cases.
  • Fixed an issue where the Super Administrator role was assigned to newly created Site Admins.

UniFi Protect Application 2.8.35

  • Added notification for G5 enhancer installation.
  • Fixed the cursor type when the user hovers over the disabled mute button.
  • Optimized G5 enhancer installation UX.
  • Improved playback and mp4 export start time selection.
  • Enhanced the remote connection stability between the console and the user.
  • [UP-Sense] Improved the accuracy of battery percentage.
  • [UP-Sense] Optimized Bluetooth connection stability.
  • ​​Updated Viewport firmware to version 1.2.77.
  • Update Sensor firmware to version 1.2.0.
  • Improved NVR stacking stability.
  • Fixed unable to reset the secondary NVR when resetting the primary
  • Fix the setting problem of the device side panel due to wrong permissions issues.
  • Fixed users with Full Management permissions could not see the Delete button on the Detections page.
  • Fixed unable to play detection-only mode recordings in rare cases.
  • Fixed an issue where backups did not restore global settings.
  • Fixed wrong system log message when lens got unplugged or re-plugged.
  • [Viewport] Fixed unable to show the live feed from G2-Bullet cameras.
  • [Viewport] Fixed full white screen when selecting a different live view.
  •  
  • Sharing live streams does not work when using a browser on an iOS mobile device.
  • You cannot receive notifications from Child Consoles.
  • You cannot pair devices if they aren’t managed by the same console in a stacked configuration.
  • You cannot transfer cameras between consoles if they are on different subnets in a stacked configuration.
  • Custom role permissions don’t sync after transferring cameras between consoles in a stacked configuration
  • [AI DSLR] License Plate Recognition doesn’t work properly.

Version 3.1.15

Version 7.5.174

Version 2.8.28

UniFi OS 3.1.15 includes the improvements and bugfixes listed below.

  • Added notifications for settings changes.
  • Added disk warning when a space IO error occurs.
  • Added lifespan support for KINGSTON OCP0S31024Q-A0 SSDs.
  • Added notifications for changing SSH passwords in System Logs.
  • Added support for IGMP Proxy.
  • Added LCM/LED settings to Console settings.
  • Added an Internet health widget in the dashboard.
  • Added support for modifying the local admin avatar.
  • Added more NTP servers.
  • Allow grouping devices.
  • Allow editing Local Credential when an admin has both UI Account and Local Credential.
  • Allow local login using cached UI Account credentials while remote services are down.
  • Improved IPsec Site-to-Site VPN stability.
  • Improved Admins page UX.
  • Improved internet check resiliency.
  • Improved stability for installing and upgrading applications.
  • Improved storage-related notifications.
  • Improved login failure messages.
  • Improved UniFi OS update resiliency.
  • Improved SSH password validation.
  • Improved remote connection resiliency.
  • Improved PPPoE connection stability when IP6CP negotiation fails.
  • Improved firmware download process.
  • Improved Remote Access Login failure reason detection.
  • Improved UX for Custom Role editing on mobile devices.
  • Improved stability.
  • Improved setup UX via mobile apps.
  • Removed the Early Access badge from the Connect application.
  • Migrated Direct Remote access feature to UniFi OS.
  • Changed the default credentials to ui/ui.
  • Uninstalled applications no longer back up.
  • Applications are no longer bundled by default. Instead, required applications will prompt to install when new devices are detected.
  • Allow users to restore specific applications during console setup and in the settings.
  • Improved setup speed.
  • Updated references to UniFi App on screen while waiting for setup.
  • Updated the Privacy and Security page during setup.
  • Updated the UI logo during setup and on the screen.
  • Disconnect all SSH sessions after setup.

Backup

  • Allow restoring backups between different console models.
  • Improved Cloud Backup UX.
  • Improved backup restore resiliency
  • Redirect to the new subnet if the subnet is different after restoring a backup.
  • Keep network settings from the setup wizard when restoring a backup file during setup.
  • Create backups even if some of the applications fail to export. Failures are reported in the system log.
  • Fixed an issue where MSS Clamping was not applied to the console’s outgoing traffic.
  • Fixed camera permission assignment issue when doing it through UID.
  • Fixed an issue where “Transfer Ownership” would appear for the old owner after transferring ownership. The button did not work for the previous owner.
  • Fixed DHCP unicast renew not using the CoS parameter.
  • Fixed broken avatars in rare cases.
  • Fixed disabled applications are starting after a reboot.
  • Fixed missing WiFi Channel information in some cases.
  • Fixed some threats that were not being blocked correctly.
  • Fixed an issue where Traffic Identification would stop working after some time.
  • Fixed console might appear as Offline in the Network application when it fails to fetch Geo-Location data.
  • Fixed Suspicious Activity consuming high memory in rare cases.
  • Fixed rare Traffic Rules scheduling issues when selecting Saturday and Sunday.
  • Fixed missing console update notifications.
  • Fixed wireless scheduling.
  • Fixed unable to load backups during setup in rare cases.
  • Fixed timezone validation issue, preventing console setups.
  • Fixed link issue when using a UF-RJ45-1G module.
  • Fixed rare upload crash.
  • Fixed network connectivity loss when remote OpenVPN Client subnet conflicts with local subnets.
  • Fixed an issue where the interface for Teleport VPN stays when disabling the feature.
  • Fixed DNS leak when using Mullvad VPN.
  • Fixed unable to establish Site-to-Site VPNs using DH groups 19, 20, 21, 25, 26, 27, 28, 29, 30, 31, 32.

UniFi Network Application 7.5.174 adds animated topology support, additional IPsec Site-to-Site configuration options, and client device latency testing.

  • A new option found in the client-side panel that tests the latency by pinging from the UniFi gateway to the client.
  • Added support for DNS Shield. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console with version 3.2 or newer.
  • Added Switch-related System Logs in its Property Panel.
  • Improved Traffic Monitor UX.
  • Added time estimate when filtering by clients
  • Improved filtering and navigation
  • Improved Dashboard UX.
  • Added confirmation when trying to set Primary/Secondary WAN to ports that are not connected to the Internet.
  • Added messaging for regions where 6GHz is not (yet) supported.
  • Added validation for unreachable custom Echo/Internet Verification Servers.
  • Added support for opening side panels while staying on the same page. E.g., opening a Client property panel while being on the Dashboard.
  • Added validation for checking Honeypot IPs against Fixed IPs from Clients.
  • Added Guest authorization by admins in the System Logs.
  • Added the “Manage” option to the Profiles settings.
  • Added support for running a speed test on WAN2.
  • Added Radio Antenna selection for UWB-XG.
  • Automatically restore from recovery backup after replacing the HDD on a UCK G2 Plus.
  • Improved setup flow for Windows/macOS.
  • Improved STP Discarding UX in the Port Manager.
  • Improved auto-backup schedule limits on UniFi Consoles.
  • Improved Data Retention options on UniFi Consoles.
  • Improved Voucher creation process.
  • Improved searching in Settings.
  • Improved Settings section organization.
  • Improved Firewall Rules table UX.
  • Improved Network Application loading time.
  • Improved Device update resiliency by using cached firmware to update a device if the device fails to download the firmware from our servers.
  • Improved adding/editing administrators on Network Application servers.
  • Improved displaying of link speeds in device property panels.
  • Improved memory usage in certain environments.
  • Improved error messaging in Port Manager.
  • Improved Traffic Rule validation when selecting too many countries. Max 150 countries/regions are supported.
  • Updated the packet loss display in the Dashboard Internet Health graph.
  • Updated the UniFi Network Device display names.
  • Display email addresses for guests authorized via Facebook authentication.
  • Prevent enabling Device Isolation on networks with managed UniFi Devices.
  • Prevent offering IP addresses to clients that are configured via a Static IP on UniFi Devices.
  • Moved AP Site Settings and Support to Advanced Settings.
  • Moved Port Manager to the Overview tab for Switches.
  • Moved the Signal column next to the Experience column on the Clients page.
  • Bundle Java inside the Application on Windows Network Application Servers.
  • Aggregate Honeypot hit and Device Reconnected notifications.
  • Always allow disabling Fixed IP addresses for clients.
  • Use channel 4 as default during adoption for UBB/UBB-XG.
  • Changed Rx/Tx error threshold for System Logs.
  • Enable auto-update for Meshed APs. Previously they would not auto-update.
  • Reorganize Firewall and Routing Settings.
  • Removed minutes from the auto speed test scheduler. It will select a random minute within the configured hour to run the test.
  • Removed Update Service Resiliency improvements that override the DNS servers for the UI domains. We’ll add messaging in a future release.
  • Removed incorrectly generated Outside of Range messages in System Logs.
  • Removed scheduled Nightly Channel Optimization tasks, you can still optimize manually.
  • Removed pre-configuration messaging from RADIUS profiles.
  • Removed fallback IP address messaging if the site does not have a UniFi Gateway.
  • Require MongoDB 3.6 or newer. This also drops support for 32-bit systems.
  • Added real-time internet traffic visualization to the Topology.
  • Added a Tooltip for Realtime Internet Traffic.
  • Display the current Connection session in the Clients and Topology pages. This works only for local connections and on unifi.ui.com (Google Chrome only).
  • Added ISP/Modem in the Topology.
  • Added 6GHz clients to the Topology.
  • Added Latency Test option to the Client Devices page. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console with version 3.1 or newer.
  • Added support for adjustable column width for Devices and Client tables.
  • Added the Last Seen and Connection type filter to the top bar on the Client Devices page.
  • Improved displaying OpenVPN Server Clients on the Clients page.
  • Added Device Type filtering to the Device page.
  • Added the ability to reset the sorting preferences by clicking Restore Defaults on the Devices page.
  • Improved UniFi Devices table columns.
  • Added affected clients to the IP Conflict notification.
  • Added Client Session Time widget to the Client property panel.
  • Added global IPv6 support in the Network Settings. This requires you to have IPv6 enabled on WAN.
  • Added IPv6 DNS servers in the Internet Settings. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console.
  • Added IPv6 stateless option in the Internet Settings. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console with version 3.2 or newer.
  • Added IPv6 addresses for client devices. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console with version 3.2 or newer.
  • Improved IPv6 Network Settings UX.
  • Improved Site-to-Site VPN configuration.
  • Added support for FQDN/Hostnames with IPsec Site-to-Site VPNs. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console with version 3.2 or newer.
  • Added support for adding a /32 and /31 to Remote Gateway/Subnets for VPNs. This requires a UniFi Next-Gen Gateway or UniFi Gateway Console.
  • Added additional ESP DH Group Options for Site-to-Site VPNs.
  • Improved the validation of WireGuard VPN Keys.
  • Improved the VPN Creation process by prefilling the name and port.
  • Improved feedback for the OpenVPN Configuration File download button.
  • Added AP Density widget to the WiFi Coverage page.
  • Improved AP Group Selection in the WiFi Settings.
  • Added DFS Scanning status for Access Points.
  • Improved Broadcasting AP column in the WiFi Settings.
  • Improved Global WiFi Settings UX.
  • Renamed WiFi QoS to WiFi Speed Limit.
  • Deprecate Facebook-WiFi authorization. Facebook is dropping support for it.
  • Improved Device connection state when adopting Mesh APs after enabling Wireless Meshing.
  • Added support for re-adopting Wireless Meshed APs that are factory reset via the Reset button.
  • Automatically enable Wireless Meshing when doing a Wireless Adoption.
  • Fixed the inability to delete Firewall rules.
  • Fixed page crash when accessing offline device settings.
  • Fixed an issue with loading statistics when using MongoDB 4.4 on a Network Server.
  • Fixed unable to adopt U-LTE devices on UniFi Gateway Consoles running UniFi OS 3.1.
  • Fixed various gateway configuration issues.
  • Fixed L3 switches were not provisioning after editing L3 Static Routes.
  • Fixed rare Network Application crashes.

UniFi Protect Application 2.8.28 introduces a wide range of new AI features, including detection highlight in the live view player and auto-tracking on G4-PTZ, and support for global recording settings for your cameras. We have also optimized the overall system UX speed, providing users with a faster and more seamless experience. Furthermore, we have enhanced the stability of both Protect and the console, ensuring even greater reliability and performance.

  • Added “Global Recording Settings” for cameras.
  • Added camera capacity on the dashboard.
  • Added “When to Record” column in the devices list.
  • Added Detection Highlight to the live view player for AI camera models and G4-PTZ.
  • Added responsive UX for the dashboard.
  • Added IP Address/Port/Uptime to the dashboard.
  • Added a “Select All” checkbox on the Playback and Detections page.
  • Added support for Smart Detection to trigger a paired FloodLight.
  • Added a capacity tooltip when hovering over the bar in the dashboard.
  • Added support for admin/role management migration to the UniFi OS level. This migration will occur of your console runs UniFi OS 3.1.11 or newer.
  • Updated the behavior of the Previous and Next event buttons.
  • Improved BLE device adoption experience when having multiple UniFi Consoles.
  • Improved application resiliency in cases of storage failure or unexpected shutdowns.
  • Improved camera auto-adoption stability.
  • Improved the camera player window UX.
  • Improved display options for Device list and System log sections.
  • Improved system log messaging and consolidated frequent logs.
  • Improved thumbnail loading on the dashboard.
  • Improved pop-out player position on small screens.
  • Improved loading time of live streams.
  • Updated the Camera firmware version to 4.64.144.
  • Updated the Viewport firmware version to 1.2.72.
  • Updated the Chime firmware version to 1.4.0
  • Updated the FloodLight version to 1.10.3
  • [G4-Doorbell-Pro] Improved the time it takes to apply image settings.
  • [G4-Doorbell-Pro] Improved audio quality when using two-way audio.
  • [G4-Doorbell-Pro] Added support for downloading clips from the Package camera.
  • [G4-Doorbell-Pro] Enable the path light when viewing the package camera via the Web UI.
  • [G4-Doorbell-Pro] Improved stability when using a PoE adapter.
  • [Doorbell-Series] Improved package detection model for enhanced accuracy.
  • [G4-PTZ] Added support for Person auto-tracking.
  • [G4-PTZ] Support more presets and home view features.
  • [G4-Pro] Improved Auto Focus.
  • [G5-Dome] Improved audio quality.
  • [G5-Series/G4-Instan/AI-Series] Improved image quality performance.
  • [G5-Bullet/Flex/Bullet] Improved audio quality.
  • [G5-Bullet/Dome/Flex] Improved image quality.
  • [G5-Series/G3-Instant/G4-Instant] Added support for adding polygon privacy zones.
  • [AI-Series/G3/4-Instant/G5-Series] Improved low-light performance.
  • [Wireless Cameras] Improved firmware update resiliency.
  • [Wireless Cameras] Improved connectivity resiliency.
  • [AI-Series] Improved the stability of detection in live view.
  • Two-Way Audio: Improved two-way audio latency.
  • [Viewport] Improved stability while streaming multiple cameras.
  • [UP-Chime] Improved update time estimation
  • [UP-Chime] Fixed unable to connect to different Access Points.
  • [UP-Chime] Fixed missing clarification for Chime disabled notifications.
  •  
  • Improved factory default process when removing a device from the application.
  • Added the ability to move cameras between the parent/child NVRs.
  • Added an NVR column in the devices list that lists which NVR manages the camera.
  • Improved Stackable UNVR initialization setup flow.
  • Fixed missing custom rules issue on stackable consoles.
  • Fixed unable to create a system config backup via the UniFi OS on stacked console setups.
  • Fixed inaccurate WiFi signal level colors.
  • Fixed delayed update of cycle mode and interval in the live view editor.
  • Fixed unable to cancel adding new live views.
  • Fixed inaccurate dates/times for some detections.
  • Fixed the timelapse table sorting after changing the camera.
  • Fixed inaccurate total time for “door open” events in UP-sense.
  • Fixed player pop-out for live view might be blank after a mouse click on Safari.
  • Fixed the Sensor side panel might not show activities in rare cases.
  • Fixed custom roles might go missing after restarting/upgrading the application.
  • Fixed unable to download timelapse clips that are 600x and 30 seconds long.
  • Fixed unable to click on zoom-in/out buttons on the Playback page.
  • Fixed push notifications for package detections are not sent.
  • Fixed a rare Viewport adoption issue.
  • Fixed a rare recording loss issue on new setup consoles.
  • Fixed application crash during startup.
  • Fixed rare application crash when recycling recordings.
  • Fixed unable to see any devices as console owner.
  • Fixed unable to adopt Viewport in rare cases.
  • Fixed incorrect timelapse export size estimates.
  • Fixed inaccurate timezone in snapshot filenames.
  • Fixed incorrect tab icon size on the detections page.
  • Fixed bitrate rounding in the camera property panel.
  • Fixed Smart Detection section isn’t appearing after a camera is adopted.
  • Fixed rare cases where “Camera Lost Power” appears unexpectedly on the playback page.
  • Fixed incorrect file names for ongoing events.
  • Fixed devices getting stuck in the “Preparing Update” state.
  • Fixed incorrect storage information on the NVRs Touchscreen.
  • Fixed missing CO/Smoke alarm events on the detections page.
  • [G3-Micro] Fixed camera going offline when switching between SSIDs with incorrect passwords.
  • [G3-Flex]: Fixed an issue that might cause low video quality due to faulty streaming adaptive bitrate control.
  • [G4-Instant]: Fixed audio performance degradation.
  • [G4-Pro/Dome/Bullet/Doorbell(-Pro)] Fixed contrast adjustment malfunctioning.
  • [G4-Pro]: Fixed an issue that might cause the image to flip unexpectedly.
  • [G4-Doorbell-Pro]: Fixed a device reboot issue while a user was in two-way audio mode already and then pressed the button.
  • [G4-Doorbell-Pro] Fixed mic does not work in some rare cases.
  • [G4-PTZ]: Fixed loss of focus when HDR is toggled.
  • [AI-Series]: Fixed loading wrong AWB parameters.
  • [AI-Series/G3,4-Instant/G5-Series]: Fixed HDR hunting under flat light sources.
  • Two-way Audio: Fixed an issue that might cause talkback to malfunction.
  • Sharing live streams does not work when using a browser on an iOS mobile device.

Additional information

  • Create a backup before upgrading your UniFi Network Application in the event any issues are encountered.
  •  

Unifi Network Native Application for UniFi OS
A specific application version that is only compatible with the UDM and UDR (running UniFi OS 3.1.6 or newer).
 – The UniFi OS update uses the application version that is required for your console.
 – The manual update process via SSH requires you to use the compatible package. Incompatible packages will be rejected on installation.
 – Older UniFi OS versions (before UniFi OS 3.1.6) on the UDM and UDR still use regular UniFi Network Application for UniFi OS.